Link Engine Management Plug-In ECU (Manual Transmission ONLY) - Nissan GTT R34 RB25DET NEO

Manufacturer: Link Engine Management
Product # {{ productPartNumber }}

$ 1,750 00
$ 1,487 50
15% off
Approx. CA$2,073.52

Manufacturer: Link Engine Management
Product # {{ productPartNumber }}
Product not eligible for promotional or discount codes.

No Customer Questions Yet

Have any questions about this product? Ask a question here.

Ask a Question

No Reviews Yet

Be the first to tell the world about this product.

Shipping Included

$ 1,750 00
$ 1,487 50
15% off
Approx. CA$2,073.52

Product not eligible for promotional or discount codes.

Description

Easy to install. Affordable. Reliable.

G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car. This ECU fits inside the factory OEM enclosure. Installation is a breeze, with no alteration of the factory wiring loom required for the models listed below.

The NGTTX is Designed to suit the grey plug RB (typically neo) engine.

  • Please check your connector matches the header in the listed photo before purchasing.
  • This ECU works for manual transmissions only.
  • Note: This ECU does not currently output the 4WD signal required for proper 4wd operation in 4WD Stageas and Skylines.
  • Note: Models fitted with factory traction control - TCS will no longer function, the TCS and slip lamps will be illuminated
  • Check the features for I/O expansion options
Suitable Applications


RB20DE NEO, RB25DE NEO and RB25DET NEO in R34 Skylines
RB20DE NEO, RB25DE NEO and RB25DET NEO in C35 Laurels
RB20DE NEO, RB25DE NEO and RB25DET NEO in Nissan Stageas
Plus, non neo motors in Stageas

G4X PlugIn Key Features (where applicable):
  • Up to 6D fuel and ignition mapping
  • Precision closed loop cam control (four cam, independent control)
  • Sequential fuel delivery
  • Digital triggering, all OEM patterns
  • OEM idle hardware supported
  • 5D boost control with three switchable tables
  • Motorsport features - antilag, launch, flat shift
  • Continuous barometric correction (on board)
  • CAN port
  • QuickTune - automated fuel tuning
  • Individual cylinder correction
  • USB tuning cable included
  • Stats recording into on-board memory
  • Gear compensations for spark, boost and fuel
  • Real time selectable dual fuel, ignition and boost maps
  • Sync and crank sensors can be a combination of Hall effect, variable reluctance or optical
  • Boost control referenced to gear, speed or throttle position
  • 512 MB data logging memory
  • Staged injection
  • Knock with "windowing"
I/O Expansion Options:

The following expansion connector inputs/outputs are provided:
Expansion connector 1

  • SGnd - Sensor Ground Only
  • +5V Out - Low Current +5V Supply
  • DI 7 - Digital Input
  • DI 8 - Digital Input
  • An Volt 10 - Analog 0-5V input
  • An Volt 9 - Analog 0-5V input
  • Ign 7 - Ignition 7 Auxiliary Output
  • Ign 8 - Ignition 8 Auxiliary Output


Expansion connector 2

  • SGnd - Sensor Ground Only
  • +5V Out - Low Current +5V Supply
  • DI 5 - Digital Input
  • DI 6 - Digital Input
  • An Volt 5 - Analog 0-5V input
  • An Volt 6 - Analog 0-5V input
  • An Temp 2 - Temperature sensor input
  • An Temp 3 - Temperature sensor input
  • *Pin 108 – OBD1 wire now used for IAT on Temp 4

No Customer Questions Yet

Have any questions about this product? Ask a question here.

Ask a Question

No Reviews Yet

Be the first to tell the world about this product.

Copyright 2024 Concept Z Performance