Search results

Create the page "Engine" on this wiki! See also the search results found.

• Idle Control
  ...as any minor running issue tends to manifest itself quite heavily when the engine is idling. This is compounded by the fact that, because the Z32 has such a ...wheel while idling, for example). The additional idle speed is to help the engine compensate for the added load of these accessories, rather than simply stal
  7 KB (1,172 words) - 21:57, 5 April 2018
• Ignition Timing
  ...s or upgrades will require a change to the ignition timing settings of the engine.<br /> <br /> <br /> ''Source: Wikipedia.''<br /> ...hamber temperatures, as well as resulting in reduced power output from the engine.<br />
  13 KB (2,148 words) - 21:57, 5 April 2018
• Injector Testing
  # Remove the throttle cable cover (on the center of the engine, with the "NISSAN" logo on it. ...r2.JPG|thumb|Ohm-testing an injector. This obviously isn't installed in an engine, but the procedure is the same.]]
  7 KB (1,215 words) - 21:57, 5 April 2018
• Intake Manifold
  ...ents to provide sufficient filtering area within the tight confines of the engine bay. Only a single airflow meter was used, but the junction where the duct
  5 KB (836 words) - 21:57, 5 April 2018
• Intake Manifold Removal
  ...lly after doing various deletes/bypasses), it involves removal of multiple engine technologies, from coilpacks and vacuum lines, to fuel lines and EGR tubes. ...f you left the PCV hoses connected, allow the rear to tip back towards the engine.
  11 KB (1,888 words) - 21:57, 5 April 2018
• Intercooler
  ...rottle body, to help cool the recently-compressed air before it enters the engine.<br /> <br />
  3 KB (446 words) - 21:58, 5 April 2018
• Jacking Up The Z
  ...the front crossmember--this is the structural piece that crosses under the engine oil pan. NOT the radiator support--never lift the car from the radiator sup
  4 KB (623 words) - 21:58, 5 April 2018
• Lifter
  ...xpand in order to minimize such a gap as well as provide smoother, quieter engine operation without requiring difficult and expensive maintenance.<br /> <br ...ask on the Z32), these lifters, when functioning properly, provide quieter engine operation.<br /> <br /> [I would like a picture of a Z32 cylinder head wit
  12 KB (2,111 words) - 21:58, 5 April 2018
• Lower Intake Manifold
  When retrofitting Phase II injectors into a Phase I engine, a traditional way of adaptation was to machine the Lower Intake Manifold t
  2 KB (278 words) - 21:58, 5 April 2018
• NA-TT Differences
  *When looking in the engine bay, Twin Turbos have four intake pipes visible, while NAs have two. *When looking in the engine bay, 90-93 Twin Turbos had [[HICAS|HICAS]] solenoids mounted near the power
  5 KB (805 words) - 23:10, 29 June 2018
• New Owner's Guide
  ==Engine== ...dler) fails, the pistons will smash into the valves, and you'll need a new engine.
  3 KB (478 words) - 21:58, 5 April 2018
• Oil Cooler
  ...l to the air, and lowering the oil temperature before it's returned to the engine (directly or the pan).<br /> <br /> ...ature, send a larger amount of oil to the cooler, and directly back to the engine (rather than the oil pan).<br /> <br />
  1 KB (225 words) - 21:58, 5 April 2018
• Oil Filter
  '''Oil filters''' are, as their name suggests, units that filter engine oil as it passes through.<br /> <br /> # Remove the engine oil drain plug (14mm, passenger side) from the engine oil pan.
  2 KB (299 words) - 21:58, 5 April 2018
• Oil Filter Tree
  ...lter Tree''' or Oil Filter Bracket is a bracket mounted to the side of the engine block, which provides a vertical mounting point for the [[Oil Filter|oil fi [[Category:Parts]][[Category:Engine Components]]
  2 KB (322 words) - 21:58, 5 April 2018
• Oil Pan
  ...p''' is a large metal pan mounted to the underside of the engine. It holds engine oil, to be drawn up by the [[Oil Pump|oil pump]] via the [[Oil Pickup Tube| ...g or drifting their Z, these are an invaluable upgrade to help protect the engine and prevent oil starvation.<br /> <br />
  3 KB (506 words) - 21:58, 5 April 2018
• Oil Pressure Sending Unit
  ...y for the oil pressure gauge, and is not monitored by the ECU or any other engine control components.<br /> The OPSU location on a USDM (LHD) engine. Image from<br /> [http://www.twinturbo.net/nissan/300zx/forums/general/vie
  4 KB (630 words) - 21:58, 5 April 2018
• Oil Pump
  ...es pressurized oil to various components in the engine. It is vital to the engine's performance and longevity. <br /> <br /> ...via the [[Oil Pickup Tube|oil pickup tube]], and pumps it through various engine components such as the crankshaft, bearings, oil squirters, cam journals, c
  3 KB (428 words) - 21:58, 5 April 2018
• Oil Squirter
  ...block">'''Oil Squirters''' or '''Oil Jets''' are small jets mounted to the engine block which spray oil upwards at the undersides of the pistons, in order to
  469 bytes (78 words) - 21:58, 5 April 2018
• PCV Delete
  ...ness, but for the most part, it is an accepted method to help simplify the engine bay. ...ead to the back of the engine, and remove the lines ''at'' the back of the engine.
  4 KB (634 words) - 22:59, 7 January 2020
• PCV Reroute
  ...he intake valve cover, point towards each other (towards the center of the engine).<br /> [[File:PCVReroute6.jpg|frameless|alt=PCVReroute6.jpg]] ...instead for a cleaner look. This allows you to run the hose closer to the engine without fear of degradation from heat damage.<br /> [[File:PCVReroute22.jpg
  3 KB (539 words) - 21:58, 5 April 2018

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)