Looks like you're using an unsupported browser, so some features might not work. We recommend upgrading your browser for a better experience.

Nistune E85 Flex Fuel Ethanol Content Analyzer Board 300ZX Z32

Manufacturer: Nistune
Product # {{ productPartNumber }}
In stock

$ 99 95

Manufacturer: Nistune
Product # {{ productPartNumber }}
In stock

Customer Questions

Question:

can i buy just the plug and not the board ? - anthony solorio

Answer:

Hi Anthony, unfortunately we do not sell the plugs by themselves.

Question:

If I use this, which I really want to, will I be able to use ethanol content gauge, or will I have to find a way to split the signal. - Laterrick

Answer:

Hi Laterrick, you would not be able to run this and a gauge at the same time. You woulud be better off using a gauge that also has an analog output (most do), and connecting that output signal directly to the ECU. This would essentially do the same job as this product would, anyway.

No Reviews Yet

Be the first to tell the world about this product.

Login to Write a Review
This product may not be legal for use on emissions-controlled motor vehicles in your area or region. Please check your local, state, and federal laws before ordering. Learn More

This product is intended for off-road/competition use, and may not be legal for use on highway or street vehicles in your area. Some products sold by Concept Z Performance may solely be used on vehicles in sanctioned competition, which may never be used upon a public road or highway, unless permitted by specific regulator exemptions (such as CARB E.O.).

It is the responsibility of the installer and/or user of the product to ensure that it is used in compliance with all applicable laws and regulations. Concept Z Performance holds no responsibility, either implied or otherwise, for any mechanical, electrical, or emissions failure resulting from using any aftermarket or performance products. Buyer assumes all risk of injury or loss which may result from using this product in a manner for which it is not intended.

Additional resources:
EPA Tampering Policy
SEMA Emissions Requirements by State

$ 99 95

Description

Nistune now supports Flex Fuel on the Z32, giving you the ability to run E85 and other ethanol blends and have the ECU adjust timing, fuel, and cranking maps based on the ethanol content. Instead of purchasing an expensive external ethanol content analyzer, Nistune has also developed dedicated Flex Fuel Boards which are small enough to be installed directly into the ECU!

The Flex Board produces a 0-5V output based on the ethanol content read by your standard GM-style ethanol sensor. This is wired directly into the ECU, replacing the diagnostics screw potentiometer (you can still easily run diagnostics through Consult). Once enabled in Nistune, you can then tune your car to trim the AFRs, cranking maps, and timing (on a full 16x16 map) based on the percentage of ethanol content. No more having to pick the "closest match" manually by reading a gauge, and no more guessing and crossing your fingers that the fuel at the pump has the right amount of ethanol for your tune!

Each Nistune Flex Board includes a pigtail to be routed through the hole left by the diagnostics selector, and a full-length harness that can be run down to your ethanol sensor, so you can still easily unplug and remove the ECU from the car (without having any kind of harness hard-wired into other controllers or switches).

Please note: The GM-style ethanol content sensors have "tabs" on their connectors which will, at first, conflict with the harness included with this kit. These harnesses are used for cost-savings. Just trim down the tabs on your ethanol sensor, and the connector will fit fine and the sensor works great.

Compatibility

If you have questions about vehicle fitment, please contact us.

Customer Questions

Question:

can i buy just the plug and not the board ? - anthony solorio

Answer:

Hi Anthony, unfortunately we do not sell the plugs by themselves.

Question:

If I use this, which I really want to, will I be able to use ethanol content gauge, or will I have to find a way to split the signal. - Laterrick

Answer:

Hi Laterrick, you would not be able to run this and a gauge at the same time. You woulud be better off using a gauge that also has an analog output (most do), and connecting that output signal directly to the ECU. This would essentially do the same job as this product would, anyway.

No Reviews Yet

Be the first to tell the world about this product.

Login to Write a Review

Copyright 2024 Concept Z Performance